-
titanium plate
Titanium plate manufacturing process
Hot forging is a forging process that is performed above the metal recrystallization temperature.
Hot rolling is a rolling process carried out at a temperature higher than the recrystallization temperature.
Cold rolling process in which the plastic deformation temperature is lower than the recovery temperature.
Annealing: a metal heat treatment process in which the metal is slowly heated to a certain temperature, maintained for a sufficient time, and then cooled at an appropriate speed (usually slow cooling, sometimes controlled cooling).
Pickling: immerse the parts in an aqueous solution such as sulfuric acid to remove the oxide and other thin films on the metal surface. It is the pretreatment or intermediate treatment of electroplating, enamel, rolling and other processes
-
Titanium plate
Characteristics of titanium plate
1. The titanium seed plate is an oxide film on the surface, which is equivalent to a good durable and wear-resistant hair separation agent. The use of titanium seed plate saves the separation agent, makes the electrode plate easy to peel, and eliminates the pretreatment process of the seed plate. The titanium seed plate is half lighter than the copper seed plate.
2. The service life of titanium seed plate is more than 3 times that of copper seed plate, and can reach 10 to 20 years according to the operating conditions.
3. The electrolytic copper made from titanium seed plate has compact crystal structure, smooth surface and excellent quality.
4. Since the titanium seed plate does not need to be coated with a separating agent, the pollution of copper electrolyte can be avoided.
5. Improve the production capacity and reduce the production cost of electrolytic copper, so as to have better economic benefits.
-
Stainless steel lap joint stub end
Size:
Seamless (Seamless) 1/2″-24″ (DN15-DN600)
Welded 1/2″-48″ (DN15-DN1200)
Standard: ASME B16.9, MSS SP-43
Thickness: SCH5S-XXS
Material (Grade): 304/L/H, 316/L/Ti/H, 317L, 310/S, 347/H, 321/H,
904/L, S32750/SAF2507, S32205/SAF205, S31803, S32760
SMO254, NO4400, N06600, N06625, N08020, N08800, No8810, N08825, N10276
-
threaded-rtj-flange
ANSI Standard : ASME B16.5 B16.36 B16.47(MSS SP-44,API 605) B16.48 Type : Welding Neck Flanges, Slip on Flanges,Threaded Flanges,Socket Welding Flanges, Blind Flanges, Orifice Flanges,Lap Joint Flanges, Ring Joint Flanges, Long Welding Neck Flanges, Figure 8 Blanks Perssure Grade : Class 150 300 400 600 900 1500 2500
-
Stainless steel Lap Joint Stub End
Easy installation: For example, the equipment has not yet arrived, but the pipeline has been installed and arranged in advance, then the flange with short flange is used. After the equipment arrives, there is always no problem with the flange. Because the flange is movable, the short connection is welded with the pipeline during welding, and the flange can move between the short connection and the pipeline.
-
Polypropylene flange
Features
Excellent chemical corrosion resistance: grooved plastic-lined pipe fittings have good acid, alkali and salt resistance properties.
-
Lap Joint Stub End Pipe
A pup joint is a commonly used accessory in industrial pipe connections. There are common threaded short sections, which are divided into double-ended outer wires, single-ended outer wires, and flat-ended outer wires, as well as short sections connected by flanges.
-
LAP JOINT STUB END
When the flanging line is a straight line, the deformation of the flanging is transformed into bending, so it can also be said that bending is a special form of flanging. However, the deformation of the blank during bending is limited to the rounded part of the bending line, while the rounded part and the edge part of the blank are deformation areas during flanging, so the flanging deformation is much more complicated than the bending deformation.
-
WELCOME TO Cangzhou Lion Pipeline technology Co., Ltd.
